Fire and Smoke Damage Restoration in SYLMAR, California

Soot, smoke odor, and charred framing handled by a local crew that answers 24/7.

Fire and Smoke Damage Restoration in SYLMAR, California starts the moment you call. We board up what is open, pull soot off surfaces before it etches, and run air scrubbers so smoke odor does not settle into your walls. Whether the fire was a kitchen grease flare or an attic electrical short, our team works the same day to stop secondary damage and get your home or business back to livable.

Firefighters respond to a building fire, battling smoke in an urban residential area.

What Fire and Smoke Damage Restoration in SYLMAR, California Involves

Fire and Smoke Damage Restoration in SYLMAR, California is the process of removing soot, neutralizing smoke residue, drying water left by firefighting, and repairing the structural damage a fire leaves behind. It is not just cleaning. Soot is acidic and etches glass, metal, and finished wood within days. Smoke pushes into wall cavities, attic insulation, and HVAC ducts, which is why a room can look clean and still smell like a campfire weeks later. Restoration means treating the whole building, not just the visible burn zone.

In SYLMAR, we see the same handful of scenarios repeat. Kitchen grease fires leave a sticky protein film that ordinary cleaners smear around. Winds through the San Fernando Valley push smoke into attics and eaves, and older ranch homes along the foothills often have original lumber and drywall that hold odor longer. If you are searching for fire and smoke damage restoration near me SYLMAR, the priority is speed: the first 48 hours decide how much of your structure and belongings are salvageable.

Why Homeowners Call Us After a Fire

Why Homeowners Call Us After a Fire

A fire is over in minutes. The damage keeps compounding for weeks unless someone stops it. Here is what proper restoration buys you.

Stop Secondary Damage

Soot etches glass and pits chrome within 72 hours, and water from hoses soaks into framing fast. We start extraction and soot removal the same day, which is the difference between refinishing a cabinet and replacing it. Our fire and smoke cleanup and restoration SYLMAR crews bring air movers and dehumidifiers on the first visit.

Odor That Actually Leaves

Smoke odor hides in insulation, upholstery, and ductwork. We pair HEPA air scrubbers with thermal fogging and ozone treatment so the smell is neutralized at the source, not masked. Most homes need two to four treatment cycles over five to seven days before the air tests clean.

Insurance Paperwork Handled

We document everything with photos, moisture readings, and line-item scope notes your adjuster can use. Working with a fire and smoke damage restoration company SYLMAR CA with insurance help means fewer back-and-forth delays and a claim that reflects the real scope of work.

Belongings Saved, Not Tossed

Furniture, clothing, and documents are often recoverable with the right method. Dry ice blasting lifts soot from wood and fabric without abrasion, and charcoal odor absorbers pull residual smell from enclosed spaces. We sort salvageable from unsalvageable and give you a written inventory before anything leaves your property.

What to Expect During Restoration

Five stages, from the first phone call to the final walkthrough. You will know what is happening at each one and who is doing it.

1

Emergency Board-Up

We arrive, secure open windows, doors, and roof openings with plywood and plastic sheeting, and shut off utilities if needed. This stops rain, animals, and theft from adding to the loss. Most board-ups take 60 to 90 minutes, and we photograph every opening before and after.

2

Assessment and Scope

A technician walks the property with a moisture meter and thermal imaging camera to map where heat, smoke, and water traveled. We test soot residue type, check attic and ductwork, and write a scope that separates structural repair from cleaning. You get the findings in plain language, not jargon.

3

Soot and Smoke Removal

Dry soot comes off first with HEPA vacuums so it does not smear. Then surfaces are cleaned with the right agent for the residue type, from grease film to protein smoke. Walls, ceilings, framing, and HVAC components are all on the list. This stage usually runs two to four days on a typical house fire.

4

Drying and Deodorization

Water from firefighting gets pulled with extraction units, then air movers and dehumidifiers run until framing reads normal on the moisture meter. Thermal fogging and an ozone generator neutralize odor in cavities and ducts. Expect three to seven days of equipment run time depending on how wet the structure got.

5

Repairs and Final Walkthrough

Drywall, insulation, paint and primer, trim, and roofing shingles go back in to California Building Standards Code (Title 24) where the work touches permitted systems. We do a final odor check and walk the property with you room by room. You sign off only when the space is clean, dry, and ready to live in.

Trained to IICRC and California Standards

Fire restoration is a trade with real standards behind it. Our technicians train to the IICRC Fire and Smoke Restoration Technician (FSRT) and Odor Control Technician (OCT) curricula, which cover residue identification, cleaning chemistry, and deodorization science. We follow NFPA 921 fire investigation standards when reading burn patterns so we understand where a fire started and how far it traveled. Work is performed under a California Contractors State License Board (CSLB) license, and our crews hold OSHA 10-Hour Construction Safety training. We are a new company, founded in 2026, and we built our process around these standards from day one rather than retrofitting them later.

  • IICRC Fire and Smoke Restoration Technician (FSRT) trained crews on every job
  • IICRC Odor Control Technician (OCT) protocols for smoke in walls and HVAC
  • NFPA 921 fire investigation standards used to read burn patterns and smoke travel
  • CSLB-licensed contractor performing structural repair after fire
  • OSHA 10-Hour Construction Safety training on all field staff
Trained to IICRC and California Standards

Why SYLMAR Picks Us for Fire and Smoke Damage Restoration

We are local, we answer the phone at any hour, and we document the job the way an adjuster needs it. Here is what that looks like in practice.

Same-Day Response

We aim to be on site within 60 to 90 minutes for emergencies in SYLMAR and the surrounding San Fernando Valley. Board-up and water extraction start on the first visit, not the second. That speed is what keeps a small fire from becoming a full gut.

Written Scope, No Surprises

You get the scope and pricing before work begins. If we find hidden damage behind a wall, we stop, show you photos, and update the scope before proceeding. No line items appear on your invoice that you did not approve first.

Insurance Coordination

We work directly with adjusters, send photo documentation and moisture logs, and use industry-standard pricing so your claim moves. If you need fire and smoke damage restoration services in SYLMAR California with insurance help, we handle the paperwork side so you can focus on your family.

Local Building Knowledge

SYLMAR has a mix of mid-century ranch homes, newer infill, and commercial buildings along the boulevard. Each one dries and repairs differently. We know which walls are plaster versus drywall and how Title 24 permitting affects your rebuild timeline before we start.

What Fire and Smoke Damage Restoration Includes

Every job starts with an assessment and a written scope, and the inclusions below are standard on a typical house fire. Structural repair, contents cleaning, and ductwork are scoped based on what the fire actually touched. You will see each item on the estimate before work begins, so there are no surprises when the invoice arrives.

What's Included

Emergency Board-Up and Security

Plywood, plastic sheeting, and temporary locks on any opening the fire or firefighting created. This stops weather, animals, and theft from adding to the loss. Most board-ups take 60 to 90 minutes and are photographed before and after.

Soot and Residue Removal

HEPA vacuuming of dry soot, then wet cleaning with the right agent for the residue type. Walls, ceilings, framing, cabinets, and fixtures are all cleaned. We do not paint over soot, because it bleeds through within months.

Water Extraction and Drying

Firefighting water gets pulled with extraction units, then air movers and dehumidifiers run until framing reads normal on a moisture meter. This is what prevents mold growth in the first 48 hours. Drying typically takes three to seven days.

Odor Neutralization

Thermal fogging, ozone treatment, and charcoal odor absorbers target smoke molecules in wall cavities, furniture, and HVAC. We run cycles until the air reads clean, not just until the visible soot is gone.

Contents Cleaning and Inventory

Furniture, clothing, and documents are sorted, cleaned where possible, and inventoried in writing. Dry ice blasting handles wood and fabric without abrasion. You get a written list of what was saved, what was cleaned, and what was not salvageable.

Structural Repair and Rebuild

Drywall, insulation, lumber, plywood, roofing shingles, paint and primer, and sealant go back in to California Building Standards Code (Title 24) where permits apply. We pull the permits and coordinate inspections so the rebuild passes the first time.

Problems We Solve After a Fire

The fire is the obvious problem. These are the ones that show up days later if nobody addresses them. We handle all of them on the same job.

Problem

Smoke odor lingering in walls and HVAC

The smell returns every time the heater or AC runs, and guests notice it at the front door. Masking sprays make it worse by adding a second odor on top of the first.

Solution

We clean the ductwork, run HEPA air scrubbers and negative air machines to pull particles out of the air, and thermal fog the cavities where smoke settled. Treatment runs until the air reads clean, usually three to seven days.

Problem

Soot residue etching glass and pitting metal

Soot is acidic. Within 72 hours it fogs glass, pits chrome, and stains finished wood in a way that cannot be polished out. Waiting a week can mean replacement instead of cleaning.

Solution

Dry soot is HEPA-vacuumed first so it does not smear, then surfaces are cleaned with the right agent for the residue type. We start the same day we arrive, which is why the first 48 hours matter so much.

Problem

Water damage from firefighting efforts

Hoses leave hundreds of gallons in framing, insulation, and flooring. Mold can start in 24 to 48 hours, turning a fire claim into a fire-and-mold claim.

Solution

Extraction units pull standing water, then air movers and dehumidifiers run until the moisture meter reads normal. We log readings daily so you and your adjuster can see the structure drying.

Problem

Charred structural framing and roof damage

Charred lumber loses load capacity, and an open roof lets weather in. This is the difference between a repair and a rebuild, and it has to be assessed before anything is covered up.

Solution

We map the damage with a thermal imaging camera, remove what has lost capacity, and rebuild to California Building Standards Code (Title 24). Permits and inspections are part of the scope, not an afterthought.

When to Call for Fire and Smoke Damage Restoration

1

A kitchen grease fire flared up and was put out with a extinguisher, but the cabinets and ceiling are sticky and the smell is spreading.

Solution:

We degrease the range hood, cabinets, and ceiling with the right agent for protein residue, then run air scrubbers and thermal fog the kitchen and adjacent rooms. The sticky film has to come off completely or the odor returns with humidity.

Outcome:

Most kitchen jobs finish in three to five days, and the room smells like a kitchen again instead of a campfire.

2

An attic fire from a roof or wiring issue smoldered for hours and smoke pushed into every rafter bay and the second-floor ceilings.

Solution:

We remove contaminated insulation, clean and seal the framing, check the roof deck for hidden char, and treat the whole house with a thermal fogger. Ductwork gets cleaned because attic smoke finds its way into the HVAC.

Outcome:

The attic is clean, the framing is sealed, and the air in the living space reads clean on the final check.

3

A bedroom fire was contained to one room, but smoke and water from the hoses reached the hallway, closet, and carpet padding.

Solution:

We remove contaminated soft goods, extract water, dry the framing, and clean hard surfaces in the adjacent rooms. Contents are sorted and inventoried before anything leaves the property.

Outcome:

The bedroom and hallway are dry and odor-free, and the family is back in the home in under a week.

4

An electrical fire burned inside a wall of a commercial building, and the burned-wire smell spread through the whole floor.

Solution:

We clean the residue, identify the failed circuit, coordinate with a licensed electrician, and phase the work so part of the space can stay open. Documentation is prepared for the commercial carrier.

Outcome:

The space reopens in phases, the electrical system is signed off, and the smell does not return when the HVAC runs.

Tools and Methods We Use

Tools & Equipment

Thermal fogger

Vaporizes a deodorizing agent into a fog that reaches the same cavities smoke reached. Used after soot removal to neutralize odor at the source.

Ozone generator

Oxidizes smoke molecules in enclosed spaces like closets, vehicles, and empty rooms. Run on a timer with the space sealed and unoccupied.

HEPA air scrubber

Filters fine smoke particles out of the air while cleaning is underway. Keeps soot from settling back onto surfaces that were just cleaned.

Negative air machine

Creates a pressure differential so smoke and dust move out of the work zone instead of into clean rooms. Standard on multi-room jobs.

Thermal imaging camera

Finds hidden heat damage and moisture inside walls without opening them. Used during assessment to map how far the fire and water traveled.

Moisture meter

Reads moisture content in framing and drywall. We log readings daily to confirm the structure is drying and to document the job for your adjuster.

Dry ice blaster

Lifts soot from wood, brick, and fabric without abrasion or water. The go-to method for furniture and surfaces that cannot take wet cleaning.

Methods

IICRC FSRT and OCT protocols

Residue identification and cleaning chemistry follow the IICRC Fire and Smoke Restoration Technician and Odor Control Technician standards. That means the right agent for the residue type, not one cleaner for every surface.

NFPA 921 fire pattern reading

We read burn patterns to understand where the fire started and how smoke traveled. That tells us which cavities and ducts to clean, so we are not guessing at the scope.

Containment and pressure control

Plastic sheeting and negative air machines keep the work zone separate from the rest of the building. This is how we clean a kitchen without spreading soot into the bedrooms.

Documented drying

Moisture readings are logged daily until framing reads normal. The log goes to your adjuster, which is often what gets a claim approved without a second visit.

How Restoration Runs in SYLMAR

SYLMAR sits at the north end of the San Fernando Valley, where dry winds and older housing stock shape how a fire job goes. The Santa Ana wind events push smoke into attics and eaves fast, and homes along the foothills often have original lumber and plaster that hold odor longer than modern drywall. Mid-century ranch homes are common, and many have attic insulation that has never been replaced, which means smoke settles there and has to be removed rather than cleaned. Commercial buildings along the boulevard have flat roofs and HVAC units on top, and smoke finds its way into those ducts quickly. When you call for fire and smoke damage restoration and odor removal in SYLMAR, California, we stage equipment based on the property type and the wind conditions that day. Canyon roads in Kagel Canyon and Lopez Canyon can slow a crew down, so we route trucks before we leave the yard. Permits run through the local building department under California Building Standards Code (Title 24), and we pull them as part of the scope so your rebuild does not stall at inspection.

Service Areas

Sylmar foothills

Homes near the foothills see wind-driven smoke pushed into attics and eaves. Attic insulation and rafter bays get checked on every job here.

Kagel Canyon

Narrow canyon roads and larger lots change how we stage equipment. We route trucks ahead of time and bring compact units where access is tight.

Lopez Canyon

Rural lots and detached structures mean a fire can involve multiple buildings. We scope each structure separately so the insurance claim is accurate.

Olive View

A mix of older homes and newer infill. Plaster walls in the older homes hold smoke odor longer and need different cleaning methods than drywall.

Local Considerations

Santa Ana wind events pushing smoke into attics

Smoke travels farther into rafter bays and eaves than on a still day. We check the attic and roof deck on every job during wind season, not just when the fire was near the roof.

Older ranch homes with original lumber and plaster

Plaster and old-growth lumber absorb smoke odor more deeply than modern materials. Cleaning takes longer and thermal fogging is usually required, not optional.

Flat-roof commercial buildings with rooftop HVAC

Smoke enters the ductwork quickly and spreads through the whole floor. Duct cleaning and air scrubbers are standard on commercial jobs here.

Kitchen Grease Fire, Sylmar Ranch Home

Before

A grease fire on the stove was put out with an extinguisher, but the protein smoke left a sticky film on the cabinets, ceiling, and range hood. The smell had spread into the living room within two days, and the family was eating outside.

After

We degreased the cabinets, ceiling, and hood, ran HEPA air scrubbers for three days, and thermal fogged the kitchen and living room. The final air check read clean, and the family was back to cooking in the kitchen on day five.

Maintenance & Follow-up

Wipe the range hood filter monthly and keep a lid within reach of the stove. A yearly degreasing of the hood keeps grease from building up again.

Before

An attic fire from a roof issue smoldered for hours. Smoke pushed into every rafter bay and down through the second-floor ceilings. The insulation was contaminated and the burned-wire smell had reached the bedrooms.

After

We removed the insulation, cleaned and sealed the framing, checked the roof deck for hidden char, and treated the whole house with a thermal fogger. Ductwork was cleaned. Six days later the air read clean and the bedrooms were back in use.

Maintenance & Follow-up

Have the roof inspected annually and keep the attic vents clear. Replacing attic insulation after any fire is worth it, because smoke settles there and does not come out with cleaning.

Before

An electrical fire burned inside a wall of one unit and left char in the framing. The burned-wire smell spread through the whole floor, and the tenant had nowhere to stay while the wall was open.

After

We secured the unit the same night, removed the charred framing and drywall, replaced the insulation, and coordinated with a licensed electrician. The unit passed inspection on the first try and the tenant moved back in on day nine.

Maintenance & Follow-up

Have the electrical panel checked by a licensed electrician every few years, and replace any outlet that feels warm to the touch. Most electrical fires start at a loose connection.

What Fire and Smoke Damage Restoration Costs

Typical 2026 pricing in SYLMAR runs $3,500 to $18,000 for a residential job, with board-up alone at $400 to $900. A small kitchen fire sits at the low end. A whole-house fire with structural repair sits at the high end. What moves the number is square footage, how far smoke traveled, whether water damage is involved, and how much framing has to be replaced. We give you a written scope before work begins, and if we find hidden damage we stop and show you before the scope changes. Affordable fire and smoke damage restoration near me SYLMAR means a price you can see before you commit, not a surprise invoice.

Pricing Factors

Square footage affected

A single room costs less than a whole floor because there is less surface to clean and less air to scrub. Smoke travel is the variable most people underestimate, since a kitchen fire can push odor through a 1,500 square foot house.

Residue type

Grease and protein smoke from a kitchen fire are stickier and take longer to clean than dry soot from a fast-burning fire. The cleaning agent and the number of passes change with the residue.

Water damage from firefighting

Hoses leave hundreds of gallons in framing and flooring. Drying adds days of equipment run time, but skipping it risks mold and a much larger claim.

Structural repair scope

Charred framing, roof decking, and drywall replacement add material and labor. Permits and inspections under California Building Standards Code (Title 24) are part of this line item.

Contents cleaning

Furniture, clothing, and documents can often be saved with dry ice blasting and the right cleaning method. The volume of contents and how much is salvageable affects the total.

Access and staging

Canyon properties in Kagel Canyon and Lopez Canyon can need compact equipment and longer staging time. Driveway access and parking affect how fast a crew can work.

Investment Range

$3,500 - $18,000 for most residential jobs, with board-up alone at $400 - $900

Based on project scope

Value You Get

The price reflects the work: soot removal, drying, odor treatment, and structural repair done to code. Skipping a step to save money usually costs more later, because smoke odor and mold both come back. A written scope protects you from that.

Frequently Asked Questions

Have questions? We have answers.

Call Us
How much does fire and smoke damage restoration cost in SYLMAR California?

Most residential jobs in SYLMAR run $3,500 to $18,000 in 2026, with a small kitchen fire at the low end and a whole-house fire with structural repair at the high end. Square footage, how far smoke traveled, and whether water damage is involved drive the number. Board-up alone is often $400 to $900. We give you a written scope before work starts so the price is not a mystery.

Can fire and smoke damage be restored in SYLMAR CA?

Yes, most of it can. Soot-stained walls, smoke-odorized framing, and water-damaged drywall are routinely restored rather than replaced. The exceptions are charred structural lumber that has lost load capacity and anything melted or burned through. A technician can tell you within the first visit which materials are salvageable and which need to come out, usually within 30 to 45 minutes of walking the property.

Who does fire and smoke damage restoration near me in SYLMAR?

We do. Our crew covers SYLMAR, Pacoima, San Fernando, Arleta, Mission Hills, and the rest of the San Fernando Valley. We are reachable 24/7 at (833) 929-6186, and we handle both the cleaning side and the structural repair side, so you are not coordinating two contractors. Ask for the scope in writing and a start date before you commit.

Does insurance cover fire and smoke damage in SYLMAR CA?

In most cases, yes. A standard homeowners policy covers the fire itself, smoke damage, and water used to put the fire out, typically up to your dwelling coverage limit. What is often not covered is damage from neglect after the fire, like mold that grew because drying was delayed. We document conditions on arrival so the cause is clear, and we work directly with your adjuster to keep the claim moving.

Credentials and Reviews

Certifications

IICRC Fire and Smoke Restoration Technician (FSRT) by IICRC
IICRC Odor Control Technician (OCT) by IICRC
California Contractors State License Board (CSLB) License by California Contractors State License Board
OSHA 10-Hour Construction Safety by OSHA

Reviews

Google

They came out the same night a kitchen fire sent smoke through the house. Boarded up the window, pulled the soot off the cabinets, and ran scrubbers for four days. The smell is gone and they handled the insurance photos. I did not have to chase anyone for an update.

Yelp

An attic fire left smoke in every rafter bay. They removed the insulation, cleaned and sealed the framing, and thermal fogged the whole house. Six days and the air was clean. They walked me through each room before I signed off, which I appreciated.

BBB

Electrical fire in my duplex. They secured the building the same night and had a written scope to me the next morning. Drywall and insulation were replaced and the unit passed inspection on the first try. The written inventory of what was saved was a nice touch.

Related Services

Smoke Damage Restoration

Smoke travels farther than flame. We clean and deodorize wall cavities, attic insulation, and ductwork so the smell does not return when the heat comes on. This is the most common add-on to a fire and smoke damage restoration job in SYLMAR.

Smoke Damage Restoration

Fire Damage Clean Up

Debris removal, charred material haul-off, and surface cleaning after the fire is out. We bag and dispose of burned contents, sweep the structure, and get it to a state where restoration work can begin. Usually the first 24 to 48 hours of a job.

Fire Damage Clean Up

Emergency Fire Damage Restoration

Board-up, water extraction, and soot stabilization on the same day you call. This is what stops a small fire from turning into a mold and rot problem. We answer the phone at 2 a.m. the same as at noon.

Emergency Fire Damage Restoration

Structural Repair After Fire

Framing, drywall, insulation, roofing shingles, and finish work put back to code. We pull the permits and coordinate inspections so your rebuild passes the first time. This is the final stage of most restoration projects.

Structural Repair After Fire

Odor Removal After Fire

Thermal fogging, ozone treatment, and charcoal odor absorbers target smoke molecules in walls, furniture, and HVAC. We run treatment cycles until the air reads clean, not just until the visible soot is gone.

Odor Removal After Fire

Soot Removal

Dry soot is vacuumed with HEPA equipment before any wet cleaning, because wiping it first smears it into the surface. We match the cleaning agent to the residue type, from grease film to protein smoke, so finishes are not damaged.

Soot Removal

Smoke Remediation

A deeper pass for smoke that has penetrated building materials. We use air scrubbers with HEPA filtration and negative air machines to pull particles out of the air while we clean the source. Often paired with duct cleaning.

Smoke Remediation

Fire and Flood Restoration

When hoses and sprinklers leave as much water as the fire left smoke, both problems get handled together. Extraction, drying, and dehumidification run alongside soot removal so mold does not get a foothold in the first 48 hours.

Fire and Flood Restoration

24 hour Fire Restoration

Fires do not keep business hours, so neither do we. Call at any hour and a crew is dispatched. Night and weekend response is the same as weekday, and board-up happens on the first visit.

24 hour Fire Restoration

Fire Damage Restoration Near Me

If you are searching from your phone in the driveway, we are close. We cover SYLMAR and the surrounding Valley neighborhoods, so drive time is short and we can be on site while the fire department is still finishing its report.

Fire Damage Restoration Near Me

Attic Fire Restoration

Attic fires are sneaky. They smolder in insulation and framing and leave smoke in every rafter bay. We remove contaminated insulation, clean and seal framing, and check the roof deck for hidden char before repairs begin.

Attic Fire Restoration

Kitchen Fire Cleanup

Grease fires leave a sticky protein film that ordinary cleaners spread around. We use the right degreasers and clean the range hood, cabinets, and ceiling. The smell of a kitchen fire can linger for months if the residue is not fully removed.

Kitchen Fire Cleanup

Commercial Fire Restoration

Restaurants, retail, and offices need to reopen fast. We phase the work so part of the space can operate while restoration continues, and we document everything for your commercial carrier. Board-up and security come first.

Commercial Fire Restoration

Electrical Fire Cleanup

Electrical fires leave char inside walls and a burned-wire smell that spreads through the whole structure. We clean the residue, identify the failed circuit, and coordinate with a licensed electrician before any power is restored.

Electrical Fire Cleanup

Hoarding Cleanup After Fire

When a fire hits a heavily cluttered home, debris removal and restoration have to happen together. We work with sensitivity, sort what can be saved, and keep the job moving so the structure can dry and be cleaned.

Hoarding Cleanup After Fire

Tenant Fire Damage Cleanup

Renters and landlords both need documentation. We photograph conditions, separate tenant belongings from structural damage, and provide a scope that works for both insurance policies. Coordination with the property owner is part of the job.

Tenant Fire Damage Cleanup

Apartment Fire Cleanup

In multi-unit buildings, smoke travels through shared walls and attics. We check adjacent units, clean common areas, and coordinate with the property manager so one unit's fire does not become a building-wide odor problem.

Apartment Fire Cleanup

Fire-Damaged Furniture Restoration

Solid wood furniture often survives with the right treatment. Dry ice blasting lifts soot without abrasion, and re-oiling brings the finish back. We give you an honest assessment of what is worth saving before anything is discarded.

Fire-Damaged Furniture Restoration

Bedroom Fire Damage Cleanup

Bedroom fires leave smoke in mattresses, closets, and carpet padding. We remove contaminated soft goods, clean hard surfaces, and treat the room until the air is clean. Most bedroom jobs finish in three to five days.

Bedroom Fire Damage Cleanup

Call for Fire and Smoke Damage Restoration in SYLMAR, California

We answer 24/7 and aim to be on site within 60 to 90 minutes. Board-up, water extraction, and soot stabilization start on the first visit. Call (833) 929-6186 and we will walk you through what happens next before we hang up.