Soot Removal in SYLMAR, California Done Right the First Time

Fast, insured soot cleanup for homes and businesses across the San Fernando Valley

Soot Removal in SYLMAR, California is what we do when smoke has settled into your walls, ceilings, and air ducts. Our IICRC-trained technicians arrive with HEPA air scrubbers, dry ice blasters, and thermal foggers to pull residue out instead of just wiping it around. We handle soot cleanup SYLMAR California homes and businesses need after kitchen fires, electrical fires, and attic fires, and we document every step for your insurance claim.

Close-up of a brick chimney stack releasing smoke, highlighting urban architecture.

What Soot Removal in SYLMAR, California Actually Involves

Soot Removal in SYLMAR, California is the process of physically removing smoke residue, char, and embedded carbon from surfaces, cavities, and HVAC systems after a fire. Soot is not ash you can sweep away. It is an acidic, oily film that bonds to drywall, paint, insulation, and lumber within hours, and it keeps eating into finishes until it is chemically lifted and rinsed. Our crews test the residue type first, because protein soot from a kitchen grease fire behaves nothing like the wet, heavy soot from a roof fire, and each one needs a different cleaning agent and dwell time.

Most SYLMAR calls we take start the same way: a small fire gets knocked down fast, but three days later the homeowner notices gray streaks creeping down the walls and a bitter smell every time the AC kicks on. That is soot that migrated into the ductwork and attic insulation. A professional soot removal after fire SYLMAR service addresses the whole envelope, not just the visible room. If you are searching for soot and residue removal near me SYLMAR, we can be on site the same day to scope the damage and set up containment before the residue spreads further.

Why SYLMAR Homeowners Book Soot Cleanup Early

Why SYLMAR Homeowners Book Soot Cleanup Early

Soot does the most damage in the first 72 hours. These are the four outcomes our customers care about most when they call us after a fire.

Stop Surface Etching

Soot is acidic and starts dulling paint, pitting chrome, and staining grout within 48 to 72 hours. We neutralize the residue with a pH-matched cleaner before it etches, which saves you from repainting entire rooms. On a typical 1,200-square-foot SYLMAR bungalow, that can mean the difference between a $600 cleaning and a $4,000 repaint.

Clear the Air You Breathe

Fine soot particles under 2.5 microns stay airborne for days and settle deep in the lungs. We run HEPA air scrubbers and negative air machines that cycle the room air 6 to 8 times per hour, capturing particles a shop vac would just blow back into the room. Families with kids or asthma notice the difference the first night.

Protect the HVAC System

Every time the furnace or AC runs, it pulls soot through the return ducts and redistributes it across the house. Our soot cleanup services in SYLMAR California include sealing and cleaning the duct runs so you are not re-contaminating clean rooms. Left alone, soot in the HVAC can total a system that would otherwise last another decade.

Preserve the Insurance Claim

Insurers pay for documented damage, not guesses. We photograph every affected surface, log moisture readings with a moisture meter, and produce a room-by-room scope with line-item pricing. That paperwork is why so many SYLMAR homeowners ask us for affordable soot cleanup near me SYLMAR and then hand our report straight to their adjuster.

Our Soot Removal Process, Step by Step

Every job follows the same five-stage sequence so nothing gets missed and nothing gets spread. Here is exactly what happens from the first phone call to the final walkthrough.

1

Emergency Assessment

We arrive, usually within 60 to 90 minutes in the SYLMAR area, and walk the structure with a thermal imaging camera and moisture meter. We identify the fire's origin pattern, map where soot traveled, and check for hidden water damage from firefighting hoses. You get a written scope and a price before any equipment comes off the truck.

2

Containment and Air Control

Crews hang plastic sheeting and zip-wall barriers to isolate the work zone, then set negative air machines so the affected rooms stay under negative pressure. That keeps soot from drifting into clean bedrooms and kitchens. HEPA air scrubbers start running immediately and stay on for the duration, cycling the air 6 to 8 times per hour.

3

Dry Soot Removal

Before any liquid touches a surface, we pull loose soot with HEPA vacuums and dry chemical sponges. On structural framing and brick, we use a dry ice blaster or soda blaster to lift char without gouging the substrate. This stage typically takes 3 to 6 hours on a single-family home and prevents the smearing that happens when wet cleaning comes first.

4

Wet Cleaning and Deodorization

Walls, ceilings, and hard surfaces get cleaned with pH-matched agents and rinsed with clean water, then dried with air movers and dehumidifiers. For odor that has soaked into framing and insulation, we deploy a thermal fogger to reach the same crevices the smoke did, followed by an ozone generator treatment in unoccupied spaces. Charcoal odor absorbers stay behind in closets and cabinets.

5

Verification and Walkthrough

We re-inspect with the thermal camera, take moisture readings, and do a white-glove wipe test on surfaces to confirm no residue remains. You walk the property with the crew lead, and we hand over a photo log plus the documentation package for your insurer. If anything fails the wipe test, we re-clean it before we pack up.

Soot Removal Expertise You Can Verify

Our technicians hold IICRC Fire and Smoke Restoration Technician (FSRT) and Odor Control Technician (OCT) credentials, and we work to NFPA 921 fire investigation standards when reading burn patterns. We are a California Contractors State License Board (CSLB) licensed contractor, and our crews carry EPA Lead-Safe Certification for pre-1978 housing, which matters in older SYLMAR stock. We follow California Building Standards Code (Title 24) requirements when repairs touch insulation, drywall, or ventilation. Every job is documented to IICRC S700 standards so your adjuster sees a scope built the way the industry expects.

  • IICRC FSRT and OCT certified technicians on every soot job
  • EPA Lead-Safe Certified crews for pre-1978 SYLMAR homes
  • CSLB-licensed contractor with workers covered under OSHA 10-Hour safety training
  • Thermal imaging and moisture mapping on every assessment
  • Photo-documented scopes built to IICRC S700 and accepted by major carriers
Soot Removal Expertise You Can Verify

Why SYLMAR Calls Us for Soot Removal

We are a local fire damage restoration company, not a call center that subcontracts your job to whoever answers first. When you book soot removal services SYLMAR, the crew that shows up is the crew that finishes the work.

Same-Day Response

Soot spreads every hour it sits. We dispatch within 60 to 90 minutes across SYLMAR and the surrounding San Fernando Valley neighborhoods, and we run 24/7 so a midnight kitchen fire does not wait until morning. Call and a real technician answers, not a voicemail box.

Insurance Documentation

We photograph every affected surface, log readings, and produce a room-by-room line-item scope your adjuster can process without back-and-forth. Homeowners tell us the report is the reason their claim moved in days instead of weeks. We work directly with all major carriers.

Containment-First Method

Cheap soot cleanup usually means a shop vac and a rag, which pushes fine particles deeper into the house. We set negative air and HEPA filtration before we touch a surface, so soot cleanup SYLMAR California families hire us for does not end with a second mess in the bedrooms.

Written Scope Before Work

You get the price before equipment comes off the truck. No surprise line items after the fact. If you have been searching for same-day soot removal services SYLMAR California and want a straight answer on cost, we will give you a range on the phone and a firm number on site.

What Our Soot Removal Service Includes

Every soot removal job we run includes assessment, containment, cleaning, deodorization, and documentation as standard. Structural repairs, insulation replacement, and content pack-out are quoted separately once we see the scope, and we tell you which is which before you sign anything.

What's Included

On-Site Assessment and Scope

Thermal imaging, moisture mapping, and a residue-type test on every job. You get a written room-by-room scope with pricing before equipment is staged, typically within 60 to 90 minutes of arrival.

Containment and HEPA Filtration

Plastic sheeting, zip walls, negative air machines, and HEPA air scrubbers running at 6 to 8 air changes per hour. This is what keeps soot from spreading into rooms that were not affected by the fire.

Surface Cleaning and Rinsing

Dry chemical sponges and HEPA vacuums first, then pH-matched wet cleaning and a clean-water rinse on walls, ceilings, cabinets, and hard surfaces. Dry ice blasting or soda blasting on framing and masonry where needed.

Odor Treatment

Thermal fogging for cavities, ozone generator treatment in unoccupied spaces, and charcoal odor absorbers left in closets and cabinets. We re-check odor at the walkthrough and re-treat if it is still detectable.

HVAC and Duct Cleaning

Sealing and cleaning the return and supply runs so the system does not redistribute soot after the rooms are clean. This is the step most cheap cleanups skip, and it is the one that causes callbacks.

Documentation Package

Photo log, moisture readings, wipe-test results, and a line-item scope formatted for your insurance adjuster. You get a copy, and we send one to your carrier on request.

Soot Problems We Solve in SYLMAR Homes

Most of the calls we take are not about the fire itself. They are about what the soot did in the days after. Here are the four problems we hear most often and how we handle them.

Problem

Gray streaks creeping down walls days after the fire

Soot migrates with humidity and settles on cooler surfaces, staining paint and grout permanently if it is not neutralized within about 72 hours.

Solution

We test the residue, neutralize it with a pH-matched cleaner, rinse with clean water, and dry the surface with air movers. On a typical SYLMAR bungalow this takes 4 to 6 hours and prevents a full repaint.

Problem

Smoke smell returning every time the AC runs

Soot trapped in the ductwork and attic insulation keeps re-contaminating clean rooms, and the smell never fully goes away until the source is removed.

Solution

We seal and clean the duct runs, replace contaminated insulation where needed, and run a thermal fogger through the cavities. Charcoal absorbers stay behind for 48 hours to catch residual odor.

Problem

Insurance adjuster pushing back on the claim

Without documented evidence of soot travel, carriers pay for the visible room only and leave the homeowner covering the rest out of pocket.

Solution

We photograph every affected surface, log moisture readings, and produce a line-item scope built to IICRC S700 standards. Adjusters accept it because it matches the format they already use.

Problem

Charred framing that looks worse than it is

Homeowners often assume charred studs mean structural replacement, which drives up cost and delays the rebuild unnecessarily.

Solution

We blast the char off with dry ice or soda blasting and inspect the remaining lumber. In many cases the framing is sound and only needs sealing and primer, which saves thousands compared to replacement.

When to Call for Soot Removal in SYLMAR

1

A kitchen grease fire that was put out fast but left a sticky film on cabinets and ceilings

Solution:

Protein soot from grease fires is nearly invisible at first and smells worse as it ages. We degrease with a pH-matched agent, fog the cabinets, and clean the range hood and ceiling in the same visit.

Outcome:

The kitchen is clean and odor-free within 24 to 48 hours, and the cabinets do not need refinishing.

2

An attic or roof fire that pushed soot into the insulation and roof decking

Solution:

We remove the contaminated insulation, blast the framing clean, treat the space with a thermal fogger, and verify with a thermal camera before closing it up.

Outcome:

The attic stops re-contaminating the living space below, and the smell does not return when the AC runs.

3

An electrical fire in a bedroom of an older SYLMAR home with original wiring

Solution:

We clean the fine, dry soot from walls and contents, coordinate with a licensed electrician on the circuit, and document the damage for both the fire claim and any code upgrades.

Outcome:

The room is safe to reoccupy, and the electrical issue is corrected before power is restored.

4

A small apartment fire where soot traveled into neighboring units through shared walls

Solution:

We contain the affected unit, run negative air so soot does not spread further, clean the shared corridor and ductwork, and document each unit separately for the landlord's claim.

Outcome:

Neighboring tenants stay in their units, and the landlord gets one clean report covering all affected spaces.

Tools and Methods We Use for Soot Removal

Tools & Equipment

HEPA Air Scrubber

Captures fine soot particles under 2.5 microns and cycles room air 6 to 8 times per hour. Runs for the entire job so particles do not resettle on clean surfaces.

Negative Air Machine

Keeps the work zone under negative pressure so soot cannot drift into unaffected rooms. Set up before any cleaning begins and checked throughout the job.

Thermal Fogger

Vaporizes a deodorizing agent into the same crevices smoke reached, including behind trim and inside cabinets. Used after surface cleaning to treat odor at the source.

Dry Ice Blaster

Lifts char and soot from framing and masonry without gouging the substrate or leaving a cleaning residue behind. Ideal for structural lumber that we want to save rather than replace.

Soda Blaster

A softer abrasive option for brick, stone, and delicate wood surfaces where dry ice would be too aggressive. Lets us clean without damaging historic or textured finishes.

Thermal Imaging Camera

Finds hidden moisture from firefighting water and maps temperature differences that reveal where soot has settled. Used at assessment and again at the final verification walkthrough.

Moisture Meter and Dehumidifier

Fires are put out with water, and trapped moisture causes mold within 48 to 72 hours. We read moisture at every wall cavity and dry the structure before the job closes.

Methods

IICRC S700 Standard

The industry standard for fire and smoke restoration. We build every scope to S700 so the cleaning sequence, documentation, and verification steps match what insurers and adjusters expect to see.

NFPA 921 Fire Pattern Reading

We read burn patterns to determine where the fire started and how smoke traveled. That tells us which cavities and duct runs to open and clean, instead of guessing and missing half the contamination.

Dry-First Cleaning Sequence

Loose soot comes off dry with HEPA vacuums and chemical sponges before any liquid is applied. Wetting soot first smears it into the surface and makes the job harder, so we never skip this stage.

pH-Matched Chemical Cleaning

Protein soot, wet soot, and dry soot each need a different cleaner. We test the residue type first, then match the cleaning agent and dwell time to it, followed by a clean-water rinse.

How Soot Removal Runs in SYLMAR Specifically

SYLMAR sits at the north end of the San Fernando Valley, and the housing stock here shapes how we do soot removal. A large share of the homes were built between the 1940s and 1970s, which means plaster walls, original wiring, and attic insulation that has never been replaced. Plaster holds soot differently than modern drywall. It is denser, so the residue sits on the surface longer and cleans up well with chemical sponges, but the lath behind it can trap odor for months if it is not fogged. Older wiring is also a factor: electrical fires are one of the most common calls we take in this area, and they leave a fine, dry soot that travels farther than grease fire residue. We also deal with the dry, windy conditions that push through the Valley in late fall and winter. When a fire happens during a wind event, soot can migrate into eaves and attic vents faster than it would on a still day, so we check the attic and roof decking on every job, not just the room where the fire started. If you need soot removal from walls and ceilings in SYLMAR, California, we scope the whole envelope before we quote. We also coordinate with your insurance adjuster and, where repairs touch insulation or ventilation, we work to California Building Standards Code (Title 24) requirements.

Service Areas

Olive View

Mid-century homes near the medical center with original plaster and older wiring. Electrical fire soot is common here, and we check the panel and attic on every call.

Kagel Canyon

Canyon properties with wind exposure and mature trees. Ember intrusion into attic vents is a real risk during fire season, so we inspect roof decking and eaves.

Hubbard Summit

Hillside homes where smoke can travel uphill fast. We often find soot in rooms far from the fire's origin, so we map the whole structure before cleaning.

El Cariso

Established residential streets with a mix of 1960s ranch homes and newer additions. Additions often have different wall assemblies, and we test each one separately.

Local Considerations

Dry, windy fall and winter wind events

Wind-driven fires push soot into eaves, attic vents, and window frames faster. We extend containment and inspection to the roof and attic on every job during these months.

Pre-1978 housing stock with lead-based paint

Sanding or dry-scraping painted surfaces can release lead dust. Our EPA Lead-Safe Certification means we use wet methods and containment that keep the dust out of the air.

Original plaster and lath walls

Plaster cleans well but the lath behind it traps odor. We fog the cavities and verify with a smell check at the walkthrough, not just a visual inspection.

Aging HVAC systems in older homes

Older ductwork is more likely to have leaks that pull soot into the system. We seal and clean the runs before the system is turned back on.

Kitchen Grease Fire in Sylmar

Before

A grease fire on a gas range sent sticky protein soot across the cabinets, ceiling, and range hood of a 1,100-square-foot home. The homeowner had wiped the walls with a damp rag, which smeared the residue into the paint and made the streaks worse.

After

We degreased the cabinets and ceiling with a pH-matched agent, fogged the hood and cabinet interiors, and ran HEPA scrubbers for 8 hours. The wipe test came back clean, and the homeowner avoided a full repaint, saving roughly $2,400.

Maintenance & Follow-up

Run the range hood every time you cook and wipe the hood filter monthly. If you smell smoke on a humid day, call us for a re-check before it sets into the cabinets.

Before

An electrical fire in the attic of a four-unit building pushed soot into two neighboring apartments through shared walls and the HVAC returns. Tenants in both units were reporting headaches and a persistent smell within 24 hours.

After

We contained the affected units, ran negative air for the duration, removed 320 square feet of contaminated insulation, blasted the framing clean, and sealed and cleaned the duct runs. All four units passed the final wipe test, and the tenants stayed in place.

Maintenance & Follow-up

Have the attic wiring inspected every 10 years and keep the HVAC filter changed every 90 days. A sealed return system is what keeps soot from traveling between units.

Before

A bedroom fire was knocked down quickly, but soot had settled on every surface in the room and drifted into the closet and hallway. The mattress, curtains, and carpet were all contaminated, and the smell had reached the living room.

After

We removed the soft goods, cleaned the walls and ceiling with chemical sponges and a wet rinse, fogged the closet, and ran an ozone treatment in the unoccupied room. The room passed the wipe test in 36 hours, and the family moved back in the same week.

Maintenance & Follow-up

Keep a working smoke alarm in every bedroom and replace the unit every 10 years. If you ever smell smoke after a small fire, call before you repaint, because paint traps odor instead of removing it.

What Soot Removal Costs in SYLMAR

Typical 2026 pricing in this area runs $450 to $2,800 for most residential soot removal jobs, with a single-room kitchen fire usually landing between $900 and $1,400. Whole-house jobs with HVAC contamination climb toward $4,000 and up. We give you a firm written price after the on-site assessment, and we document everything so your insurance claim reflects the real scope. If you have been quoted a suspiciously low number for soot cleanup SYLMAR California, ask what is included. Containment, HEPA filtration, and duct cleaning are the line items cheap quotes leave out, and they are the ones that determine whether the job holds.

Pricing Factors

Square footage affected

Soot travels. A fire in one room can contaminate 600 to 1,200 square feet once the HVAC distributes it. We measure the affected area during the assessment and price by the actual scope, not the room where the fire started.

Soot type

Protein soot from grease fires is stickier and needs more dwell time than dry soot from electrical fires. Wet soot from roof fires is heavier and requires more rinse cycles. Each type changes labor hours and chemical cost.

HVAC and duct cleaning

Duct cleaning adds $300 to $900 depending on the number of runs and whether insulation needs replacement. Skipping it is the most common reason soot reappears after a job, so we quote it upfront rather than as a surprise.

Insulation replacement

Attic and wall insulation that has absorbed soot usually cannot be cleaned and must be removed and replaced. This adds $1.50 to $3.50 per square foot, and we tell you during the assessment whether it is necessary.

Contents and soft goods

Upholstery, mattresses, curtains, and carpet absorb soot and odor. Cleaning them in place is cheaper than replacement, but heavily contaminated items are a separate line item. We assess each item and tell you what is worth saving.

Access and containment complexity

Multi-unit buildings, tight attics, and homes with additions take longer to contain and clean. We factor access into the quote so the price you get on site is the price you pay.

Investment Range

$450 - $4,000+ depending on scope

Based on project scope

Value You Get

The price reflects containment, HEPA filtration, duct cleaning, odor treatment, and a documentation package your insurer will accept. A cheaper cleanup that skips containment usually means a second job later to fix what spread, and that second job costs more than doing it right the first time.

Soot Removal Questions SYLMAR Homeowners Ask

Have questions? We have answers.

Call Us
How much does soot removal cost in SYLMAR California?

Most residential soot removal jobs in SYLMAR run $450 to $2,800 in 2026, with a typical single-room kitchen fire landing around $900 to $1,400. Whole-house jobs with HVAC contamination climb toward $4,000 and up. Square footage, soot type, ceiling height, and whether ducts need cleaning drive the number. We give you a firm written price after the on-site assessment, and we document everything for your insurance claim.

Can soot be removed from walls in SYLMAR CA?

Yes. Painted drywall, plaster, brick, and wood paneling all clean up when the right method is used. We start dry with chemical sponges and HEPA vacuums, then move to pH-matched wet cleaning and a clean-water rinse. Severely etched drywall sometimes needs a sealant and repaint, but the structure underneath is usually salvageable. We test a small area first and show you the result before committing the whole room.

Who does soot cleanup near me in SYLMAR?

We do. Fire Damage Restoration Sylmar is a local, CSLB-licensed contractor with IICRC FSRT and OCT certified technicians serving SYLMAR and the surrounding San Fernando Valley. We handle the soot removal, odor treatment, and documentation in one visit, and we can be on site within 60 to 90 minutes of your call. Reach us any hour at (833) 929-6186.

Is soot removal covered by insurance in SYLMAR California?

In most cases, yes. Standard homeowners and commercial property policies in California cover sudden fire and smoke damage, including soot cleanup, and often the cost of temporary repairs to prevent further damage. We photograph every surface, log readings, and produce a line-item scope your adjuster can process. We recommend calling your carrier to open the claim the same day you call us.

Licensed, Certified, and Documented

Certifications

IICRC Fire and Smoke Restoration Technician (FSRT) by Institute of Inspection, Cleaning and Restoration Certification
IICRC Odor Control Technician (OCT) by Institute of Inspection, Cleaning and Restoration Certification
EPA Lead-Safe Certification by U.S. Environmental Protection Agency
California Contractors State License Board (CSLB) License by California Contractors State License Board
OSHA 10-Hour Construction Safety by Occupational Safety and Health Administration

Reviews

Google

They handled soot removal after a kitchen fire in our Sylmar home. Set up containment before touching anything, cleaned the walls and cabinets, and the smell was gone in two days. The report they gave us got our claim approved without a follow-up question.

Yelp

Called at 11 p.m. after an attic fire and a real person answered. On site in about an hour, tarped the roof, and started soot removal the next morning. The wipe test at the end was clean, and they showed us the cloth.

BBB

We manage a fourplex in Pacoima and used them after an electrical fire. They contained the work zone so the other tenants could stay, cleaned the ducts, and documented each unit separately. The scope matched what our adjuster expected.

Google

Professional soot removal after a fire in our San Fernando home. They explained every step, gave us a written price before starting, and finished when they said they would. The bedroom passed the wipe test in 36 hours and we moved back in that week.

Other Fire Restoration Services We Provide

Smoke Damage Restoration

Soot removal handles the visible residue; smoke damage restoration handles what you cannot see. We pair the two so odor and fine particles trapped in insulation and framing are treated before the job closes out.

Smoke Damage Restoration

Fire Damage Clean Up

Full debris removal, char extraction, and surface cleaning after a fire. Soot removal is the detail stage of this larger cleanup, and we run both under one scope so nothing falls between contractors.

Fire Damage Clean Up

Emergency Fire Damage Restoration

Board-up, roof tarping, and immediate stabilization after a fire. Getting containment up fast limits how far soot travels before we begin the cleaning phase.

Emergency Fire Damage Restoration

Structural Repair After Fire

Once soot is removed and surfaces are verified clean, we repair charred framing, replace drywall, and match paint and primer so the room looks like the fire never happened.

Structural Repair After Fire

Odor Removal After Fire

Thermal fogging, ozone treatment, and charcoal absorbers for smoke smell that lingers after cleaning. Soot and odor are two separate problems, and we treat both.

Odor Removal After Fire

Smoke Remediation

Duct cleaning, HEPA filtration, and surface sealing for smoke that has migrated through the HVAC system. This is the step that stops soot from reappearing after the walls are clean.

Smoke Remediation

Fire and Flood Restoration

Fires are usually put out with water, which means soot and moisture damage often arrive together. We dry the structure and remove the soot in one coordinated job.

Fire and Flood Restoration

24 hour Fire Restoration

Round-the-clock dispatch for fires that happen at night or on weekends. Soot does not wait for business hours, and neither do we.

24 hour Fire Restoration

Fire Damage Restoration Near Me

Local dispatch across SYLMAR and the San Fernando Valley. If you are searching for a nearby crew after a fire, we can be on site within 60 to 90 minutes.

Fire Damage Restoration Near Me

Attic Fire Restoration

Attic fires push heavy soot into insulation and roof decking. We remove contaminated insulation, blast framing clean, and treat the space before it re-contaminates the living area below.

Attic Fire Restoration

Kitchen Fire Cleanup

Grease fires leave a protein soot that is sticky and hard to see. We use the right degreasers and dwell times to lift it from cabinets, range hoods, and ceilings without damaging finishes.

Kitchen Fire Cleanup

Commercial Fire Restoration

Soot removal for retail, office, and warehouse spaces, scheduled around your operating hours so you can reopen as fast as safely possible.

Commercial Fire Restoration

Electrical Fire Cleanup

Electrical fires leave fine, dry soot and burned wiring. We clean the residue and coordinate with a licensed electrician to make the circuit safe before power is restored.

Electrical Fire Cleanup

Hoarding Cleanup After Fire

Heavy contents make soot removal slower and more hazardous. We clear the space, remove contaminated materials, and clean the structure underneath.

Hoarding Cleanup After Fire

Tenant Fire Damage Cleanup

We work with renters and landlords to separate tenant responsibility from owner responsibility and document the soot damage for both insurance claims.

Tenant Fire Damage Cleanup

Apartment Fire Cleanup

Multi-unit fires spread soot through shared walls and corridors. We contain the work zone so neighboring units stay livable while we clean yours.

Apartment Fire Cleanup

Fire-Damaged Furniture Restoration

Upholstery and wood furniture absorb soot and odor. We assess what can be cleaned and deodorized in place and what needs replacement, then document it for your claim.

Fire-Damaged Furniture Restoration

Fire and Smoke Damage Restoration

The combined service that covers soot removal, odor treatment, and surface repair in a single documented scope, start to finish.

Fire and Smoke Damage Restoration

Bedroom Fire Damage Cleanup

Bedroom fires leave soot in mattresses, closets, and carpet. We remove the residue, treat the soft goods, and verify the room is clean before you sleep in it again.

Bedroom Fire Damage Cleanup

Get Soot Removal in SYLMAR, California Today

Soot etches deeper every hour it sits. Our IICRC-certified crews are on call 24/7 across SYLMAR and the San Fernando Valley, and we give you a written price before work starts. Call now and we will be on site within 60 to 90 minutes.